Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
This article which follows about How to Install a Bathtub Yourself is exceptionally compelling. Don't miss it.
Mounting a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately tough project. If the old tub is readily accessible, the project can move easily; if you need to open up a wall to get rid of the old tub and also place the new bath tub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have actually qualified on your own for the task and fit attempting it. Rather than working with a service provider to take over a halfway-completed job, it is better to consider utilizing one before you start. Possibilities are you might need a specialist plumber to make tube links.
This post will aid you mount a brand-new tub in your bathroom if you have actually already bought a brand-new tub and do not require to transform the arrangement of your previous water system pipes.
Your devices and also material checklist should make up the following:
Getting ready for the Installment
To start with, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the continuing to be water that will come from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to going on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Using the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water system as well as examine all joints and also new pipework for leakages as well as tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bath tub needs to wait till the tub has been utilized at least once as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the supplier supplied backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, creating the water to pass through the wall in between the bathroom and also the tiling, leading to issues with moisture as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, as well as can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to permit the movement experienced when the tub remains in use. The sealant can crack rather very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Installing A Bathtub? Make a review down the page. We'd be pleased to see your thoughts about this content. In hopes that you visit us again in the near future. Please take the time to share this article if you enjoyed reading it. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Expertise? Call us! Report this page